|
Article |
Department of Geology, University of Southampton, Southampton SO9 5NH, UK
The geometry and orientation of faults are examined using several field examples of small-scale (< lm displacement) fault systems. For isotropic rocks under triaxial compression, faults normally develop in conjugate sets about the maximum compressive stress (
Where
1), with dihedral angles usually of about 50°, as predicted by the Coulomb theory of failure. In layered rocks, the geometry of faults varies with the orientation of layering with respect to the stress field. Where 1, is approximately normal to layering or anisotropy, conjugate faults also develop symmetrically about 1. Where rocks have interbedded layers with different mechanical behaviours, however, faults tend to initiate orthogonal to the more brittle layers (i.e. originate as extension fractures sub-parallel to 1), but oblique to the less brittle layers. As the fault steps through the layering, pull-aparts are developed which may reduce the dihedral angle. Where 1 is oblique (c. 25–75°) to anisotropy, one set of faults is developed at a high angle to layering, with another at a low angle, usually showing a ramp-flat geometry. Large dihedral angles (up to 90°) may result and 1, does not bisect this angle. 1 is approximately parallel to layering, two cases can be recognized. Where 3 is approximately normal to layering, faults with layer-parallel flats and contractional ramps develop. Where 2 is approximately normal to layering, conjugate faults develop which are symmetrical about 1, the geometry resembling that in isotropic rocks. These observations are in agreement with rock deformation experiments which show the strong effect of anisotropy on fault orientation, but the observations incorporate the effects of layering of materials with different deformation characteristics.
This article has been cited by other articles:
 |
|
 |
|
  C. A. J. Wibberley, G. Yielding, and G. Di Toro Recent advances in the understanding of fault zone internal structure: a review Geological Society, London, Special Publications, 2008; 299: 5 - 33. [Abstract] [Full Text] [PDF]
|
|
|
|
|
|
W. van der Zee, C. A. J. Wibberley, and J. L. Urai The influence of layering and pre-existing joints on the development of internal structure in normal fault zones: the Lodeve basin, France Geological Society, London, Special Publications, 2008; 299: 57 - 74. [Abstract] [Full Text] [PDF]
|
|
|
|
|
|
L. Micarelli and A. Benedicto Normal fault terminations in limestones from the SE-Basin (France): implications for fluid flow Geological Society, London, Special Publications, 2008; 299: 123 - 138. [Abstract] [Full Text] [PDF]
|
|
|
|
 |
|
 N. Fredman, J. Tveranger, S. Semshaug, A. Braathen, and E. Sverdrup Sensitivity of fluid flow to fault core architecture and petrophysical properties of fault rocks in siliciclastic reservoirs: a synthetic fault model study Petroleum Geoscience, 2007; 13: 305 - 320. [Abstract] [Full Text] [PDF]
|
|
|
|
 |
|
 C. A.J. Wibberley, J.-P. Petit, and T. Rives The effect of tilting on fault propagation and network development in sandstone-shale sequences: a case study from the Lodeve Basin, southern France Journal of the Geological Society, 2007; 164: 599 - 608. [Abstract] [Full Text] [PDF]
|
|
|
|
 |
|
 R. Soliva, A. Benedicto, P. Vergely, and T. Rives Mechanical control of a lithological alternation on normal fault morphology, growth and reactivation Bulletin de la Societe Geologique de France, 2005; 176: 329 - 342. [Abstract] [Full Text] [PDF]
|
|
|
|
|
|
M. Belayneh and J. W. Cosgrove Fracture-pattern variations around a major fold and their implications regarding fracture prediction using limited data: an example from the Bristol Channel Basin Geological Society, London, Special Publications, 2004; 231: 89 - 102. [Abstract] [PDF]
|
|
|
|
|
|
C. Lansigu and R. Bouroullec Staircase normal fault geometry in the Gres d'Annot (SE France) Geological Society, London, Special Publications, 2004; 221: 223 - 240. [Abstract] [PDF]
|
|
|
|
|
|
D. C. P. Peacock Differences between veins and joints using the example of the Jurassic limestones of Somerset Geological Society, London, Special Publications, 2004; 231: 209 - 221. [Abstract] [PDF]
|
|
|
|
 |
|
 Clay smear seals and fault sealing potential of an exhumed growth fault, Rio Grande rift, New Mexico AAPG Bulletin, 2003; 87: 427 - 444.
|
|
|
|
|
|
Integrating 3-D Seismic Data, Field Analogs, and Mechanical Models in the Analysis of Segmented Normal Faults in the Wytch Farm Oil Field, Southern England, United Kingdom AAPG Bulletin, 2001; 85: 1183 - 1210.
|
|
|
|
|
|
C. S. Mansfield and J. A. Cartwright Stratal fold patterns adjacent to normal faults: observations from the Gulf of Mexico Geological Society, London, Special Publications, 1999; 169: 115 - 128. [Abstract] [PDF]
|
|
|
|
|
|
S. A. STEWART and H. W. BAILEY The Flamborough Tertiary outlier, UK southern North Sea Journal of the Geological Society, 1996; 153: 163 - 173. [Abstract] [PDF]
|
|
|
|
|
|
E. McAllister and J. R. Cann Initiation and evolution of boundary-wall faults along the Mid-Atlantic Ridge, 25-29{degrees}N Geological Society, London, Special Publications, 1996; 118: 29 - 48. [Abstract] [PDF]
|
|
|
|
|
|
S. A. Stewart, M. J. Harvey, S. C. Otto, and P. J. Weston Influence of salt on fault geometry: examples from the UK salt basins Geological Society, London, Special Publications, 1996; 100: 175 - 202. [Abstract] [PDF]
|
|
